How To Make A Faucet Cover?

Prevent your exterior faucets from freezing by installing DIY faucet covers. Quite often, people forget about covering the faucet. During the winter season, the exterior taps installed in the walls of the homestead can freeze easily. When this happens when you haven’t taken the precautions, it might cause serious damage to both interior and exterior plumbing.

Sometimes when you are lucky enough, the damage won’t burst into the walls of your house. DIY tap covers are very simple and cheap. Besides, there is no experience needed to make it, and it requires very little time.

Steps of Making A DIY Faucet Cover or How to Make a Faucet Cover

The “Do it yourself” tap cover is very simple to make and needs no experience. The steps are very simple and are not time-consuming. Learn the simple steps and get yourself set for the winter. Below are highlighted steps for making a DIY outdoor faucet cover.

Tool Needed: To begin with, you need a pair of scissors, wire cutters, gloves, and an electric drill that has a ¼ bit of drill. You can also get a beer though it is optional.

Required Material: Get a plastic container with a large perimeter, such as a Gatorade can. You will also need one-roll pipe insulation made of fiberglass. In addition to that, fence wire is also needed on hand, and duct tape or waterproof tape that measures on feet should be several of them.

All these things are found at a hardware store at affordable prices. On the contrary, you can use cloth and a straight coat hanger instead of batting and wire. Such clothes can be a pair of worn socks, among others.

Use a Drill to Bore a Hole: At the bottom of your plastic jug or can next to its end, drill a ¼ hole using the drill.

Cut the Wire: Using the wire cutter, cut the wire measuring 2 cm in length.

Fold the Wires: Take two halves of an old wire and bend them tightly, then insert them at the end of the hole “from the bottom” to secure the cover to the faucet’s body.

Cut the Insulation Strips: Put on your gloves, and then cut the insulation into various strips. The shorter strip should be six and two long strips measuring 12 each. A short strip insulates the can or jug at the bottom. Longer strips are used to insulate the inner side of the jug. Fold \the insulation wire in small lengths and its kinds of stuff at the jug’s bottom.

Wrap the jug at the Inner Bottom Side: Use the insulation wires with the longer lengths to wrap around the bottom inner part of the jug. Use the other insulating wire to wrap the jug’s inner side at the top. Allow the wire to protrude past the jug about an inch. For easy looping of the faucet’s head later, let the folded wires stick past the lid of the jug for about four or more.

Wrap the Outer Part of the Can or Jug: Wrap the outer side of the can or jug using duct tape. Also, wrap the duct about the insulation that protrudes outside the jug to prevent the insulation from becoming wet.

To install the cover on the faucet’s head, begin by looping the folded wires about the faucet’s part and then push the jug or can against the tap. Do this while pulling through the excess wire backward.

Fold the two wires that stick out f the jug’s end about the opposite side of your jug to meet at the upper side. Twist together the wires at the meeting point to secure the spigot cover. If you don’t like the look of the duct tape, you can paint it to match the color of your house.

Frequently Asked Questions

There are a lot of questions that people frequently ask to get clarification and to know much about the DIY spigot cover. Below are highlighted questions that are commonly asked.

What Is The Essence of Covering The Faucet?

Water expands naturally when it freezes. Probably you might have once left a bottle of water in a freezer for a night. The bottle was distorted. The same thing happens when water freezes n pipes. When the water in the pipes expands, it might burst or destroy the pipes. Metals are more fragile when it freezes and when the water thaws, serious leaks, and destroyed plumbing will be left.

What Are Some of The Signs of A Frozen Pipe?

When you open your tap, and there is nothing that comes out, this might result from frozen pipes. Also, you can check out if there are any signs of leakages. It is very easy to reduce the damage and cost of burst or frozen pipes.

What To Do In Case of Plumbing Leakage?

It is very difficult to determine to what extent the damage of a busted pipe will occur. So, when you act fast, you will save the damage. Below are some quick ways that will help you find the leakage.

• Do the safety check. Safety has to come first. Before acting, asses the leakage safety since it shows structural and electrical hazards. Address such safety issues and evacuate if possible.
• Turn off the water supply. Turn off the main valve that supplies water to your home and call the plumber quickly to address the issue.
• Damage control. A plumber will address the issue professionally to reduce the damage.

The Bottom Line

During the winter season, it’s good to cover the exterior taps. This will help you prevent damages that may be resulted from frost. Prepare yourself before the fall by learning the steps of DIY outdoor faucet covers. It is simple and takes very little time. Most of the materials are found around your home, and some are at the hardware at an affordable price.

As well, as learn the signs of frozen pipes early enough and take action to prevent further damage. If you open the tap and no water comes out, try pouring warm water around the tap gently or tie it with a cloth or towel soaked in hot water.